Here you will find countless questions and answers, starting from the model to choose, passing by where it will be installed, how to do it, doubts, configuration questions, spare parts the homologation process, etc etc.. Keep reading.
⇒ Where can I buy a Chinese stationary heater?
You can buy them both in China and in Spain through eBay, Amazon, y Aliexpress.
We have prepared a list with the best prices, as well as ELIMINATED sellers who cause problems. You have them separated according to power, and the type of control here you have the complete list.
In the 3 sites have buyer protection, so if it doesn't arrive, arrives damaged, or it breaks down you can complain without any problem.
We are frequently asked where it is best to buy it., if you follow our channel Facebook, we are announcing in the communications, What is the best option depending on the day?.
We always try to put offers with shipping from Spain, that take between 3-7 dias. Although it depends on the model you are looking for, It may only be available in China.. Normally for a heater customs fees are usually around €25., although it depends on how the seller declares it.
You have all the spare parts you need available in the spare parts section.
⇒ Which static heating model to buy 2kw or 5kw?
Depends on the car model, van, caravan or motorhome that you want to heat.
A small size van less than L2H2 such as VW Transporter, Opel Vivaro, Mercedes Vito or Viano with the model of 2kw It is more than enough.
We only recommend 5kw models for models above L2H2. The VW Crafter type, Opel Movano or Mercedes Sprinter of size L2H2 2kw are sufficient. Although if you opt for a 5kw one you can lower their power.
⇒ Types of programming controls
There are many versions, to see them all click HERE.
Black Square LCD Programmer
Currently there are at least 4 different versions of this screen, Before so many versions came out it was our favorite screen, right now how is it a lottery that they are going to send you, since they don't specify it, We recommend buying the ones we put here below.
Comment that this black LCD only works with this type of remote control.
Blue LCD Programmer / Roja / Golden
- Ch8
- Ch7
- Ch6
It is the same as the black LCD, but incorporates 2 news. Includes a height sensor, THAT DOES NOTHING just report the height you are at.
And the other is this remote control, It is very useful because it gives you the temperature, and you can modify it knowing at all times what you put, with the black LCD control you can't see what you are putting.
Here do you have a manual.
⇒ ¿Model “permanent” vs “portable” ?
You ask me this a lot.. and to help you choose, answer these questions yourself, to decide which one to put.
If you find yourself with the dilemma of, I have a car or small van, and you are worried about the ITV, you have the option to buy the laptop and lower the power.
But that might not be enough, because even if you lower it it could still be too hot.
In this case you can consider installing in the “Baca” or on the bike rack, even on the ground (tying it to the wheel). I'll leave you some examples so you can get an idea of what I'm talking about..
⇒ How to associate or pair the controller with the screen?
Enter in the manual from your screen and discover how to do it.
⇒ Can these be mounted under the van??
And, Can be done, same as with webasto heaters, eberspacher y planar.
The only thing that Chinese stationary heaters, They don't have the electronics in a waterproof box, That's why its price is €140 and not the €900 that the others cost..
For installation on the underside of the vehicle, we recommend using boxes that are as tight and protected as possible.. Although it is difficult to get water in, and in case it breaks down, It is very easy to repair it, the replacement costs about 15€ and you can buy it here If necessary.
⇒ Can they be mounted on the side??
And, The manufacturer indicates that there is no problem putting it on its side at a 90º angle..
⇒ What is your electricity consumption??
When it consumes the most it is at startup, which are some 10 amps, that consumption is only for less than 3 minutes.
Then, depending on the heating model, and the selected power, The fan will have a consumption between 8w and 45w.
With that consumption, you can keep it on all night without any problem, in the worst case, having it 8 hours, In the 8kw model and at maximum power it would be 360w 30ah.
In a real case, with a heating of 5kw with an average power / baja, Its consumption would be approximately 80w less than 7ah. When a Camper battery is usually at least 100ah. (Below you have a table with all the data)
⇒ How much fuel do you consume in one night??
As we mentioned before, a winter night, in the mountain, at temperatures close to 0º, Normally the heating is on low mode. / medium at most.
With a 5kw heating, with an average consumption of 0.15 (according to my experience) and with low insulation, my consumption in one night is approximately between 1, y 1,5 liters.
(Below you have a table with all the consumption data)
⇒ What configuration is best for my LCD screen??
Every person is a world, For example, I don't like it when the air blows very hot., so I have it set to about 60º so that the air doesn't dry out..
On the other hand, this may not matter to you, and you are only interested in whether it works well for height. That is why we have prepared 2 manuals you should read regarding this, so you can find the most suitable configuration for you.
Original setting is 1.6Hz – 4.5Hz – 1680 rpm – 4500 rpm – 12v – Sn1
In my case, I have it adjusted for height and with the air at about 60º with this configuration, which I am very happy.
1.4Hz – 4.5Hz – 1950 rpm – 4500 rpm – 12v – Sn1
⇒ Password to enter LCD screen settings
To date, they are known 3 different passwords, The most common and that always works is 1688. It is possible that messing around, you change it, blocks, or it doesn't work so you have these others that also work. 9009 y 9977.
⇒ Power or power mode thermostat
By default, the heating is configured in a mode in which we control the output power in HZ.
I for example, I always use it like this, adjusting at all times to power I want it to work. But it is possible to change to thermostat mode, With this mode we select a temperature and it alone adjusts the power depending on the temperature of the cabin.
For enable he thermostat mode you have to press the buttons while pressing the configuration button at the same time + above. If we want to return to the previous mode, we repeat the process.
In some rotary or roulette thermostats it is also possible to activate the thermostat mode by pressing the ON button 8/10 seconds, red will light up to confirm this mode, For power mode the LED would be Blue. In this type of thermostat, the temperature is adjusted in increments of 3 degrees.
⇒ What type of battery does the remote control use??
The type of battery used is: alkaline battery 12v A27 (diameter of 7.7 mm)
And the red/black remote control with LCD screen has 2 AAA batteries.
⇒ Installation Tips
It is common to assemble it and it not work, but I have to tell you that it is not a problem with the heating but with the assembly. These are the most common problems you will face, so read them carefully to avoid making those mistakes and ending up frustrated and disappointed with the heating..
- Do not lengthen the cable that comes with the heater. Do this, causes voltage drops, especially when the cable we use is the same thickness, or even lower.
- If you need to lengthen it, cut a piece of the one that comes standard, and replace it with a thicker one.
- Batteries in poor condition, The voltmeter may read 12v or more and we think it is fine., but it is common that when trying to start this value falls below 11v, giving error or manifesting itself by releasing a lot of white smoke.
- Lay the pump flat, and not at a 45º angle, This causes air to accumulate in the filter., and then it doesn't turn on.
⇒ How to put the fitting in the external tank that comes in the kit?
We drill in the holes marked on the tank, Be careful not to leave plastic chips inside the tank..
We pass a guide wire from the hole to the opening, We will tie the fitting at the tip and pull it inwards until we place it in position, (don't forget the o-ring) Then put the other O-ring and the nut.
We take out the guide cable, and we connect the diesel hoses.
The ideal is to use the purge mode before starting the heating., Otherwise the first start will give us an error, since with the fuel circuit empty it will not work.
If not, purge it first., probably not only does it not turn on the first time, but it costs you much more, in the following attempts.
The ideal is to start the purge mode and observe the filter until it is completely full., We will wait a few more seconds until the diesel reaches the heating and we will stop it..
If we haven't done it right, The heater will start releasing a lot of white smoke., It's totally normal, have patience, once turn on, has to burn all the diesel. To complete this it may take between 5 y 10 minutes quietly.
If it marks us error E-08 we will repeat the process. Yes on the contrary, you can't get it to start, or you get any other error you can contact us manual where you have all the error codes and how to solve them.
⇒ White smoke / soot / poor performance
There are many variables to cover regarding this problem.. Make sure the intake and exhaust pipes are clear. (It can also be due to lack of air due to the altitude.), if you have doubts, remove the two tubes.
The heating has no way of checking that combustion is adequate., so if any problem is detected it will give error E-08.
More details Here.
⇒ Important assembly considerations
Hot air inlet
The air always has to be taken from the inside. If not, Combustion gases could enter the interior. If it is not possible, take air from an area far from the gas outlet, both the vehicle engine and the heating.
The intake pipe must be protected
The intake pipe should be protected with a grille, or with the black intake filter that is usually supplied with the kit.
Cold air inlet and outlet / caliente
Air ducts do not have to have sharp curves, nor be placed in places that can be covered by any object, things, backpacks, boxes, etc..
How to check the spark plug
With a multimeter, measure spark plug resistance, It should mark between 0.40hms – 0.7ohms.
To check the resistance of the glow plug, unplug the spark plug wire from the PCB (switchboard) from the heater and measure the two wires with the multimeter set to resistance
If the result is 0 o 1 and not the values mentioned above, the spark plug is defective.
If you don't have a multimeter you can remove the heater plug., and connect it to 12v for a few seconds,. If it heats up and we see that it turns red, we disconnect immediately so as not to break it..
The spark plug works with 8v, Having it connected to 12v for too long will cause it to break..
Video of a person showing a burning spark plug and releasing smoke is circulating on Facebook, for connecting it to 12v and not 8v. This will never happen in real life., since the control unit only gives 8v to the spark plug.
| Model | heating | stationary | ||||||
|---|---|---|---|---|---|---|---|---|
| Power | Voltage | Power level | Power | Air quantity | Electrical Consumption | Diesel Consumption | Measurements | Weight |
| 2kw | 12/24 | Low | 850 | 40 | 7 | 0.10 | 310x115x122 | 2.7kw |
| Half | 1200 | 60 | 12 | 0.15 | ||||
| Alto | 1800 | 90 | 22 | 0.23 | ||||
| Very high | 2200 | 105 | 34 | 0.28 | ||||
| Model | heating | stationary | ||||||
|---|---|---|---|---|---|---|---|---|
| Power | Voltage | Power level | Power | Air quantity | Electrical Consumption | Diesel Consumption | Measurements | Weight |
| 3kw | 12/24 | Low | 850 | 40 | 7 | 0.10 | 310x115x122 | 2.7kg |
| Half | 1600 | 67 | 15 | 0.18 | ||||
| Alto | 2400 | 105 | 26 | 0.26 | ||||
| Very high | 3000 | 115 | 37 | 0.36 |
| Model | heating | stationary | ||||||
|---|---|---|---|---|---|---|---|---|
| Power | Voltage | Power level | Power | Air quantity | Electrical Consumption | Diesel Consumption | Measurements | Weight |
| 5kw | 12/24 | Low | 900 | 60 | 7 | 0.10 | 376x140x150 | 4.5kg |
| Half | 2000 | 120 | 13 | 0.25 | ||||
| Alto | 3500 | 150 | 24 | 0.38 | ||||
| Very high | 5000 | 185 | 40 | 0.51 |
| Model | heating | stationary | ||||||
|---|---|---|---|---|---|---|---|---|
| Power | Voltage | Power level | Power | Air quantity | Electrical Consumption | Diesel Consumption | Measurements | Weight |
| 8kw | 12/24 | Low | 1200 | 65 | 9 | 0.10 | 376x140x150 | 4.5kg |
| Half | 3000 | 138 | 22 | 0.35 | ||||
| Alto | 5500 | 180 | 42 | 0.54 | ||||
| Very high | 8000 | 220 | 45 | 0.73 |












Hello, I have installed a Chinese 12v heater, I did all the steps to follow, I purged with the pump until there was no more air, but I find that it does not turn on and I get an error E. 06 It tries to start but nothing happens, it ticks and nothing Esteban, can you tell me what it could be? ? very good page, thanks to everyone I was able to connect it
Hola.
I just installed a Chinese heater that works perfectly..
The problem comes when the Ducato engine starts..
I have a T connection on the 8mm tube that supplies diesel to the engine and when I start the engine a very significant amount of diesel comes out of the heating exhaust pipe..
The heating oil pump is not supposed to act as a non-return valve or not let the oil from the van pass through when the heating is stopped.?
Gracias
Hello Daniel, if it acts as a non-return, but she is not prepared to put pressure on him, From what you mention, you have the diesel pump in the Ducato's own tank., not in the engine.
In this case the diesel intake should be on the return (If it reaches the bottom of the tank) or with a spade.
Greetings.
Hello Pedro, Sorry I've been away for a few days and haven't been able to answer before..
1- The motor rotates freely with your finger or runs hard/rubs against something?
2- What voltage does the heating LCD screen indicate??
If it rotates freely, and the voltage is 12v or higher, the fault is probably in the sensor, Sometimes either from the factory or because we have opened them to mess around., When you close the plastic case, the sensor is out of place and does not detect the magnets of the fan propeller, check this photo, and make sure that the sensor is well inserted in its hole..
Greetings
Hello Esteban, if the fan is light, it starts and blows cold air. 1 o 2 minutes and it stops so I'll look at what you're telling me and I'll tell you, thank you
Hello Esteban I wanted to thank you very well what you told me about the sensor was that the problem was outside the plastic where it goes so I am very happy with my heating again thank you
I'm glad you solved it. Enjoy, greetings!
Good morning Stephen, I have one of these heaters installed 5 Kw, and the truth is that it was going great until now, but now and for no apparent reason the fan starts and stops constantly every so often.
what would it be due to?.
Thanks in advance.
Kind regards: Inigo
Hello Inigo, I would need you to make a video, you uploaded it to youtube, and send me the link to see the behavior.
Comes to pump diesel? What voltage does the battery have when you start it?? In the video you can also see the screen and the oscillation of the battery voltage.
Greetings.
Hello Esteban,
Could you tell me something about this control model??
https://amzn.to/2JavUaF
I would like to know if it has the height kit and if you know if it works well.
Gracias
Hi Jan, that model is very basic, It does not have the height nor does it allow you to configure anything.
If you need it in 2kw you have this other option: http://s.click.aliexpress.com/e/4xGb6AmU
If you want it on Amazon the cheapest is this but you would have to change the screen for the one LCD because that one he brings is a bit.. m..
Greetings.
Hello Esteban,
What I liked about that model I sent you, It is the design that seemed more webasto-like to me. But I didn't find any information anywhere..
The van I want to equip is a VW California Beach with a roof, I would say that 2kw heating is going to be enough, no?? Or do you recommend the 5kv one??
Thank you very much for your time and sharing your knowledge.!
Jan
Hola, with 2kw you have plenty! Look, this one just came out today. offer for €92.
Greetings.
Ok, Esteban,
I see that this one is at a better price and includes shipping..
https://amzn.to/33Qrqhc
I can trust?
Thanks for your help!
Jan
The one you say is the best price, the one I said they force you to send it for €100, haha internet stuff!
All the best!
Jan
They do it like this to see if you bite.. and you pay more.. Previously I only had €30 shipping costs, and then I change it.
Hola ,I just bought a Chinese heater and after connecting it to 13v the LCD screen turns on but where the voltage should appear they appear 3 lines and no button responds. Does anyone have any idea what to do?? Gracias.
Hello Pepe, If you can enter the Facebook group and send me some photos or videos, Let's see if I can find out what's wrong. It is is the link. Greetings.
Hello good, genial post, thank you so much. Monte una cale china, I start her out of the van and good., I mount it, start it again and at 2 minutes, a lot of white smoke comes out, especially from the air filter when I turn it off., What can it usually be due to?? I have to leave it on for a while? Regards, and thank you very much
But it gives some error or something? When the smoke comes out it is because there is not enough air coming in., either due to a carbon obstruction, or because the voltage drops at startup and the diesel cannot ignite.
What is the second boot like?, I opt for the battery issue, that is not in good condition, the cable is too long, of inadequate section, a bad connection, etc..